Main Composition:
α , ω -Dihydroxyl Methyl Silicone
Feature:
The product is neutrality solidifies, has the characteristics of high viscosity, the mudium module, the high flexibility and strength, and aging resistance, performance fine, there are colors of transparent, grat, porcelain white and black.
Scope Of Application:
This product are widely used for bonding of glass, rubber, lumber, ceramics, metal and textile fiber surface. This product not suitable to use in seep out the fat, the plasticizer or the solvent material surface. In the airtight place and the rime not, sucessive years immerses or all year long the moist place.
Techinical Data:
| Appearance |
Unit |
Data |
Item |
Unit |
Data |
| Appearnace |
/ |
Black even cream |
Shear Strength |
MPa |
≥ 4.0 |
| Density |
g/cm 3 |
1.2 ± 0.1 |
Elasticrecovery rate% |
% |
≥ 100 |
| Surface dry time |
Min |
20-60 |
Flexibility |
% |
≥ 400 |
| Solidify speed |
mm/24h |
2-8 |
Displacement ability |
± % |
12.5 |
| Dropping ability(N Type) |
Mm |
0 |
Shao's AHardness |
/ |
40-60 |
| Low Temperature |
C |
-40 C |
Leakage rate |
/ |
0 |
| Peel Strength |
MPa |
≥ 6.0 |
Pollution |
/ |
No pollution |
Using Method:
1. Clean the surface to get rid of the rust, oil, or any dirty.
2. Cut the cap point, twists the cap mouth, cut at 45 degree angle bevelling according to need.
3. In order to get the smooth glue, hold the bottle at 45 degree angle, squeeze the glue through cap mouth.
4. If further sealing needed, please finished operation within 5 minutes, wipe off the surplus glue with dry tissue.
5. After completely solidify, amend the glue by knife.
Warning:
1. It is not preferred for the applying at the air-tight situation. Keep ventilative during the operation as the acetic acid is released due to the chemical reaction.
2. Re clean the surface if operating could not be finished within 1 hour since first cleaning. Re clean the surface as well if rains or dirty is onto the surface again.
3. No toxic of product. But be careful not to make the glue get into the eyes or nose. Wash them at once if does.
4. Keep smooth and continuous during applying of the glue onto the sealing surface. The adhesive performance would be not good if the air get in.
5. Tighten the lid at once and take off the extrusion nozzle after gluing to avoid entering of the wet air and causing of the solidifying. Eliminate the remnants around the nozzle.
6. Remove the solidified glue on the bottleneck during re applying. The unsolidified glue inside could be used still. Store the rest glue of the bottle at air tight and shade.
1. This product will release a few acetic acid in the solidification process, the working conditions should maintain ventilate.
2. Do not put within kids reach, non-toxic after solidifies completely, avoid eye contact before solidification, if touches the eye carelessly, use massive water to wash, if serious go to see a doctor.
3. When operation, must hold the glue steadily, cannot separate, guards against mixes in the air and form bubble, affects the seal effect.
4. After operation, take off the cap mouth immediately, close the packing cover tightly to prevent the moisture enter and cause solidification. Wipe off the glue left at glue mouth.
5. This product should be operated at temperature 5-40oC, relative humidity 40-80%
Storage And Packing:
1. The product is nonflammable. Keep dry and shade, air tight during storage.
2. The shelf life is 12 months from the date of production
3. Packing specification: 300 ml/pc, in plastic barrel
HUNAN MAGPOW ADHESIVE GROUP CO., LTD
Was founded in 1989, Leaders at all levels of care and guidance, in the community friends and the majority of customers with the help and support, has gone through more than 20 years of arduous pioneering and steady development process. Companies from the original workshop-style processing plant to national "Torch Plan" implementation of enterprises, national standards of enterprises, the state's key high-tech enterprises. Group assets worth 150 million.
Audited Supplier 
){kind=link}
){kind=link}