All Purpose Motorcycle Grey Gasket Maker Silicone
Item: MPB110
Specifiction: 85g/set, 12sets/inner, 12inners/CTN
Meas: 67.3*42.8*28.9cm
Scope of application:
This product is used for sealing of car, gear case of motor, fore-and-art board, water pump, plane flange, cover board of other machine equipment.
Product Feature
This product is one kind of sulfur silicone sealant with one acid component which could be applied at any climate and could take chemical reaction with the water in air rapidly. Good aging-resistant ability, high flexible, perfect performance of high or low temperature resistant. Several machine waster water resistant, good elastic
Technical Feature:
| No. |
Item |
Technical Parameter |
| Top grade |
Common grade |
| 1 |
Appearance |
Exquisite well-proportioned cream,no agglomeration, no gelling, no surface solidify, no bubble, hard dispersing |
| 2 |
Prolapse Distance |
Vertical mm |
≤ 3 |
| plane |
No distortion |
| 3 |
Density |
0.93-0.98 |
0.93-0.98 |
| 4 |
Extrusion , ml/min |
≥ 400 |
≥ 400 |
| 5 |
Surface setting Time, mm |
5-15 |
5-15 |
| 6 |
Shao's Hardness |
20-30 |
15-30 |
| 7 |
2 3 C Standard extend |
≥ 0.4 |
≥ 0.4 |
| 8 |
Bonding destroy area under under standard condition % |
≤ 5 |
≤ 10 |
| 9 |
Elastic recover rate% |
≥ 80 |
≥ 80 |
| 10 |
Extend bond rate under standard condition |
100% no damage |
100%no damage |
| 11 |
Setting time mm/24h |
3-8 |
/ |
| 12 |
Oil-Leakage rate |
≤ 2 |
/ |
| 13 |
applying temperature |
-40~ 15 0 C |
-40~ 120 C |
rections
Directions
Diredctions
Direction
Using method
1. Cleaning up the surface with the cotton fabric, guarantees the surface not to have the dust, the greasy dirt, the rusty stain and so on.
2. In order to obtain good outward appearance, paste the temporary protection adhesive tape, near the place to be pasted after clean the surface, pull out after paste glue.
3. Pierce the seal with the cap, cover the mouth, cut bevel the tube mouth.
4. Spread the sealant evenly on the place which need to be sealed or bonded. The operation should be continuously, guarantee the sealant continuously squeeze out at cylinder shape, move the glue mouth evenly and slowly, prevent the form of bubble or hole is move too fast.
5. The sealant form shape at approximately 10 minutes, when assembly maintains the gasket thickness, fold gathers the curing at normal temperature 24 hours
Certificates
Certificates
Storage and packing:
1. This product is non-flammable, seal store in 10-27 centigrade cool dry place.
2. The shelf life for top grade acetic gasket maker s 12 months from date of production.
3. Packing 45g/PC, 85g/PC, 85PC+3G promotion in tube.
Note :
Leave thickness for gasket when reassembling. do not over-tighten bolts. remove excess silicone with dry cloth or alcohol wipe. silicone dries to touch in 1 hour. allow 24 hours to fully cure and bond. REPLACE CAP AFTER USE.
Warning:
1. This product will release a few acetic acid in the solidification process, the working conditions should maintain ventilate.
2. Do not put within kids reach, non-toxic after solidifies completely, avoid eye contact before solidification, if touches the eye carelessly, use massive water to wash, if serious go to see a doctor.
3. When operation, must hold the glue steadily, cannot separate, guards against mixes in the air and form bubble, affects the seal effect.
4. After operation, take off the cap mouth immediately, close the packing cover tightly to prevent the moisture enter and cause solidification. Wipe off the glue left at glue mouth.
5. This product should be operated at temperature 5-40, relative humidity 40-80%
HUNAN MAGPOW ADHESIVE GROUP CO., LTD
Was founded in 1989, Leaders at all levels of care and guidance, in the community friends and the majority of customers with the help and support, has gone through more than 20 years of arduous pioneering and steady development process. Companies from the original workshop-style processing plant to national "Torch Plan" implementation of enterprises, national standards of enterprises, the state's key high-tech enterprises. Group assets worth 150 million.
Magpow adhesive group FAQ:
1.Can we visit your factory?
Yes, warmly welcome to visit us at any time.
2.What's your factory address?
Our address(English):Lansi Road,changsha national biomedical base.Liuyang,HuNan,China.
We can pick up you.
3.Can you give us private design?
Yes, we offer OEM service.
4.What's your guarantee?
1-10 years.
5.Can u send samples to us ?
Yes, we can provide free samples in china.
6.How many days to produce 1*20FT container?
Big drum packages: 7-10days.
Small packages: 20-25days.
7.What are the documents we provide?
CE,CI,PL,CO / FORM E / FORM A , B/L according to your demand.
8.How do I get updated MSDS information?
Material Safety Data Sheets (MSDS), can be accessed on the Product Details Pages for the individual products, or contact the MSDS Coordinator for assistance:
Contact us, you will get more than what you see!
){kind=link}